july 2013 common mode filters for ultra high-speed differential signal line (hdmi, dvi, displayport, usb3.0, etc.) acm-d/-h series acm2012d [0805 inch]* acm2012h [0805 inch] * dimensions code jis[eia] emc components
(2/9) 001-01 / 20130723 / e9712_acm_dh.fm emc components reminders for using these products before using these products, be sure to request the delivery specifications. safety reminders please pay sufficient attention to the warnings for safe designing when using these products. the storage period is less than 6 months. be sure to follow the storage conditions (temperature: 5 to 40c, humidity: 10 to 75 % rh or less). if the storage period elapses, the soldering of the terminal electrodes may deteriorate. do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.). before soldering, be sure to preheat components. the preheating temperature should be set so that the temperature difference between the solder temperature and chip temperature does not exceed 150c. soldering corrections after mounting should be within the range of the conditions determined in the specifications. if overheated, a short circuit, performance deterioration, or lifespan shortening may occur. when embedding a printed circuit board where a chip is mounted to a set, be sure that residual stress is not given to the chip due to the overall distortion of the printed circuit board and partial distortion such as at screw tightening portions. self heating (temperature increase) occurs when the power is turned on, so the tolerance should be sufficient for the set therm al design. carefully lay out the coil for the circuit board design of the non-magnetic shield type. a malfunction may occur due to magnetic interference. use a wrist band to discharge static electricity in your body through the grounding wire. do not expose the products to magnets or magnetic fields. do not use for a purpose outside of the contents regulated in the delivery specifications. the products listed on this catalog are intended for use in general electronic equipment (av equipment, telecommunications equipment, home appliances, amusement equipment, computer equipment, personal equipment, office equipment, measurement equipment, industrial robots) under a normal operation and use condition. the products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or quality require a more stringent level of safety or reliability, or whose failure, malfunction or trouble could cause serious damage to society, person or property. if you intend to use the products in the applications listed below or if you have special requirements exceeding the range or c onditions set forth in the each catalog, please contact us. (1) aerospace/aviation equipment (2) transportation equipment (cars, electric trains, ships, etc.) (3) medical equipment (4) power-generation control equipment (5) atomic energy-related equipment (6) seabed equipment (7) transportation control equipment (8) public information-processing equipment (9) military equipment (10) electric heating apparatus, burning equipment (11) disaster prevention/crime prevention equipment (12) safety equipment (13) other applications that are not considered general-purpose applications when designing your equipment even for general-purpose applications, you are kindly requested to take into consideration securi ng protection circuit/device or providing backup circuits in your equipment. reminders
(3/9) 001-01 / 20130723 / e9712_acm_dh.fm ? all specifications are subject to change without notice. emc components common mode filters for ultra high-speed differential signal line (hdmi, dvi, displayport, usb3.0, etc.) features broadband common mode filter that was developed for gbps-level high-speed differential signal interfaces such as dvi and hdmi tm . differential mode cutoff frequency is 3.5ghz for acm2012d and 6. 0ghz for acm2012h, so they do not negatively influence high-spe ed differential signals. characteristics impedance is matched for 100 , which is set for many differential interfaces, and can suppress unnecessary reflection components. application emi measure for hdmi tm , which is an interface for digital video devices: acm2012h is ideal for senders (sources) such as digital tvs, dv d recorders, and liquid crystal projectors, while acm2012d is id eal for receivers (sink). emi measure for high-speed differential signal interfaces for digital video signal interfaces such as dvi, display port, and se rial ata used for pcs, etc. part number construction operating temperature range, package quantity, product weight the storage temperature range is for after the circuit board is mounted. overview of the acm-d/-h series acm 2012 - d - 900 - 2p - t 00 series name lwh dimensions product internal code impedance number of lines packaging style internal code (mm) ( )at 100mhz 2012 2.01.21.2 d 900 90 2p 2 lines t ?180mm reel 2.01.21.3 h tl ?330mm reel type temperature range reel diameter package quantity individual weight operating temperature storage temperature c c mm pieces/reel mg acm2012d C40 to +85 C40 to +85 ?180 2,000 10 ?330 10,000 acm2012h C40 to +85 C40 to +85 ?180 2,000 10 ?330 10,000 product compatible with rohs directive compatible with lead-free solders rohs directive compliant product: see the following for more details related to rohs directive compliant products. http://www.t dk.co.jp/rohs/ halogen-free: indicates that cl content is less than 900ppm, br content is less than 900ppm, and that the total cl and br conte nt is less than 1500ppm.
(4/9) 001-01 / 20130723 / e9712_acm_dh.fm ? all specifications are subject to change without notice. emc components overview of the acm-d/-h series recommended reflow profile preheating soldering peak temp. time temp. time temp. time t1 t2 t1 t3 t2 t4 t3 150c 180c 60 to 120s 230c 10 to 30s 245c 5s max. natural cooling t3 t1 preheating t2 soldering t3 t3 t4 t2 t1 t: time peak t: temperature
(5/9) 001-01 / 20130723 / e9712_acm_dh.fm ? all specifications are subject to change without notice. emc components acm-d/-h series acm2012d type shape & dimensions recommended land pattern circuit diagram 2.0 0.2 1. 2 0.2 1.3max. 0.5 0.3 0.05 0.3 1.2 0.4 0.4 dimensions in mm dimensions in mm 1.1 0.75 0.75 0.40.4 0.4 1 2 4 3 ? no polarity
(6/9) 001-01 / 20130723 / e9712_acm_dh.fm ? all specifications are subject to change without notice. emc components acm-d/-h series y acm2012d type electrical characteristics characteristics specification table measurement equipment ? equivalent measurement equipment may be used. impedance vs. frequency characteristics measurement equipment ? equivalent measurement equipment may be used. common mode impedance ( ) [at 100mhz] dc resistance ( )max. [1 line] rated current (ma)max. rated voltage (v)max. insulation resistance (m )min. cutoff frequency (ghz)typ. characteristic impedance ( )typ. part no. min. typ. 65 90 0.30 300 20 10 3.5 100 acm2012d-900-2p-t00 measurement item product no. manufacturer common mode impedance 4991a agilent technologies dc resistance 4338a agilent technologies insulation resistance 4339a agilent technologies product no. manufacturer 4991a agilent technologies 1 10 100 10000 1000 10000 1000 1 10 100 frequency ( mhz ) impedance ( ) 900 common mode 900 differential mode
(7/9) 001-01 / 20130723 / e9712_acm_dh.fm ? all specifications are subject to change without notice. emc components acm-d/-h series acm2012h type shape & dimensions recommended land pattern circuit diagram 2.0 0.2 1. 2 0.2 0.5 0.35 0.35 0.4 1. 2 0.1 1.2 0.4 0.4 dimensions in mm dimensions in mm 1.1 0.75 0.75 0.40.4 0.4 1 2 4 3 ? no polarity
(8/9) 001-01 / 20130723 / e9712_acm_dh.fm ? all specifications are subject to change without notice. emc components acm-d/-h series y acm2012h type electrical characteristics characteristics specification table measurement equipment ? equivalent measurement equipment may be used. impedance vs. frequency characteristics measurement equipment ? equivalent measurement equipment may be used. common mode impedance ( ) [at 100mhz] dc resistance ( )max. [1 line] rated current (ma)max. rated voltage (v)max. insulation resistance (m )min. cutoff frequency (ghz)typ. characteristic impedance ( )typ. part no. min. typ. 65 90 0.30 300 20 10 6 100 acm2012h-900-2p-t00 measurement item product no. manufacturer common mode impedance 4991a agilent technologies dc resistance 4338a agilent technologies insulation resistance 4339a agilent technologies product no. manufacturer 4991a agilent technologies 1 10 100 10000 1000 10000 1000 1 10 100 frequency ( mhz ) impedance ( ) 900 common mode 900 differential mode
(9/9) 001-01 / 20130723 / e9712_acm_dh.fm ? all specifications are subject to change without notice. emc components acm-d/-h series packaging style reel dimensions tape dimensions ty p e a w1 w2 n e acm2012d ?3302 9.50.5 13.51 1001 2 typ. ?1803 9+1/C0 131 60+1/C0 2 typ. acm2012h ?3302 9.50.5 13.51 1001 2 typ. ?1803 9+1/C0 131 60+1C0 2 typ. dimensions in mm ty p e a b ?d0 e f p0 p1 p2 w k t acm2012d 1.40.1 2.250.1 1.5+0.1/0 1.750.1 3.50.1 4.00.1 4.00.1 2.00.1 8.00.2 1.40.1 0.250.05 acm2012h 1.40.1 2.250.1 1.5+0.1/0 1.750.1 3.50.1 4.00.1 4.00.1 2.00.1 8.00.2 1.40.1 0.250.05 ?13.0 0.2 ?21.0 0.8 n e 2.0 0.5 a dimensions in mm 1.0 w2 w1 k w f e p0 p1 p2 ?d0 b a 160min. taping 440min. drawing direction 500 to 560min. dimensions in mm
mouser electronics authorized distributor click to view pricing, inventory, delivery & lifecycle information: tdk: ? acm2012h-900-2p-t000? acm2012h-900-2p-t00
|
